the biggest challenges facing the automotive industry are to increase fuel economy and lower emissions, without sacrificing power, all of which impacts materials for turbochargers and emissions systems. in spite of all the talk about electric drive systems, the industry will still rely on the internal combustion engine for the next 15–20 years while solving these challenges.
as a result, there will be significant growth in smaller internal combustion engines such as those below 2.5l. these smaller displacement engines will help deliver fuel economy and emission performance, but will likely require some type of performance boost to provide the power output that customers demand. that boost will come from devices like turbochargers.
materials for turbochargers and emissions systems must now withstand a much harsher operating environment caused by:
materials that withstand high temperatures and corrosive fluids
several dupont materials for turbochargers and emissions systems can withstand these new conditions: dupont™ zytel® plus nylon and dupont™ zytel® htn92 series ppa resins. these resins are based on our shield technology and offer a significant leap in thermal oxidation resistance or long-term heat aging performance.
applying shield technology to zytel® plus polymers improves their resistance to hot air aging. zytel® plus and zytel® htn92 series ppa maintain good strength after being exposed to 180º c hot air for 3,000 hours. these three products also retained their strength between 75 to 100 percent better than nylon 66, and about 40 to 70 percent higher than that of pps.
this improved heat aging performance means automakers can use these materials to improve the durability of components, or use these new composites to replace metal components in higher-temperature loops for cost and weight savings.
with regard to tensile strength retention, the zytel® htn92 series ppa and new zytel® plus nylon maintain more than 50% of their original properties at the end of the 2,000-hour aging test, immersing them in an egr solution.
for gaskets and sealing applications for coolers, the dupont™ vamac® aem elastomer and dupont™ viton® fkm synthetic rubber are good solutions. these elastomers provide good performance in holding up to higher temperature and fluid resistance requirements.
thermal management of turbo systems
the use of polymers in the thermal management side of turbo systems also offer potential to lower weight and reduce costs.
in charge-air coolers, cost savings could be achieved through the use of plastic end tanks. tanks made of plastic could be crimped to the metal core at a lower cost. cost savings could also be extended to the cold side of the low-pressure egr coolers.
another integration potential is to join the gasket with the end tanks though a component molding technique prior to its assembly with the core. the turbocharger resonator made with zytel® htn ppa is used in some small diesel engines. it allows complex shape design and integration, which translates into both cost and weight savings.
the cover and some components in the egr valve actuator can be made with zytel® htn ppa, allowing the integration of multiple electrical components through design resulting, once again, in cost and weight savings.
wear and friction in turbochargers & emissions systems
over the past few years dupont has applied fundamental materials science to the challenges of moving parts in turbochargers and emission systems — parts with unique wear and friction requirements.
while there are many types of wear, dupont defines wear as one object sliding against another. wear is the ability — or inability — of the substrate to resist fracturing as it attempts to resist the movement of the other object.
by defining a set of critical material properties that impact wear at high temperatures, dupont scientists have been able to demonstrate improvements in wear in the range of 60-70%.
for example, a plate on a disc system with a lubricant in between the rotating surfaces is commonly found in driveline applications, such as thrust washers and seal rings. by carefully optimizing material selection and design guidelines, while understanding the thermal needs of the system, we have been able to demonstrate 45 to 55% reduction in measured friction — a significant gain for rotating driveline components.
to achieve long life there should be little or no component wear. and for predictable response times, friction should remain constant over the life of the vehicle. when applied to downsized turbocharged engines with advanced emission control systems, the exposure conditions push the performance limits of conventional materials.
the dupont™ vespel® scp resinous plastic product family is one of the results of dupont’s study of friction and wear. vespel® scp material offers:
automakers have seen improved performance in egr valves after evaluating vespel® scp materials in emission valve applications exposed to high levels of soot and coke particles, which also contributes to both wear problems and actuation speed problems, primarily due to the change in friction properties over time.
turbocharger and emission control devices
vespel® has been successfully tested in applications such as control arm ends and linkage bushings, which are external to the turbocharger and exposed to the engine compartment environment. engineers are also considering internal bearing components such as ball bearing retainers, shaft spacers and seals.
with the increased use of electronic controls, these components must operate at very fast actuating speeds. dupont has demonstrated that, even after millions of cycles, vespel® parts retain their smooth, consistent operation.
from “art to part”
dupont offers deep, global technical support in elastomers, resins, and high-performance parts. dupont materials and application development teams continue to find new ways to integrate elastomers and resins to help automakers reduce weight and cost without sacrificing performance. dupont scientists are continuously inventing families of high-heat-resistant lightweight materials to help ensure automakers choose the most appropriate materials for turbochargers and emissions systems. dupont works throughout the value chain both locally and globally to help automakers shorten the time from “art to part.”